Case-In-Point: MTI Turbine Vibration Analyzer/Balancing System Technology Principles GalleryCase-In-Point: MTI Turbine Vibration Analyzer/Balancing System Technology Principles
Application Notes-MTI, Articles-MTI, Industry-Aerospace, Industry-Compliance Testing, Industry-Government/Military, Industry: Transportation, Knowledge Center-MTI, News-Industry, News-MTI-PBS, Whitepapers-MTI
Case-In-Point: MTI Turbine Vibration Analyzer/Balancing System Technology Principles
What do you think when you’re flying home, cruising at 30,000 feet and the drinks have just been served? Our engineers think about the ripple in the glass. That ripple signals vibration and is an indication that the engine may be in need of a balance.
Article: High-Performance Digitizers in Semiconductor Manufacturing Applications GalleryArticle: High-Performance Digitizers in Semiconductor Manufacturing Applications
Application Notes-GaGe, Articles-GaGe, Industry-Compliance Testing, Industry-Semiconductor, Industry-Semiconductor-GaGe, Knowledge Center-GaGe, News-GaGe, News-Industry, Whitepapers-GaGe
Article: High-Performance Digitizers in Semiconductor Manufacturing Applications
High-Performance Digitizers in Semiconductor Manufacturing Applications PC-based high-speed, high-resolution digitizers perform critical data acquisition functions during semiconductor fabrication, die packaging, and final chip testing. Introduction Data acquisition is a critical element of quality control and compliance testing during three stages of semiconductor manufacture. The first stage is fabrication, in which single-crystal semiconductor wafers are subject to various operations that leave them imprinted with micro-circuitry patterns. During the second stage, the wafers are diced up into individual silicon “die” that are packaged into final chips. The third stage involves functional testing of the final chips to [...]
The Cost of Failing to Inspect Semiconductor Wafers
This is the second of three articles in Semiconductor Wafer Measurement for Increased Profitability. The first article in this series explains why disc geometry matters. The third article describes the benefits of using semi-automated, fully-automated, and manual systems for wafer metrology and inspection. Most semiconductor wafers are made of silicon, the second most common element in the Earth’s crust. Yet, silicon’s abundance does not mean that wafers are inexpensive. The pure form of silicon that’s used in semiconductors does not occur naturally and must be refined and mixed with a dopant that alters material properties and electrical characteristics. Silicon ingots are formed, wafers [...]
Cable & Wire Troubleshooting Made Easy-Using the MTI 1510 Precision Signal Generator
Cable & Wire Troubleshooting Made Easy Using MTI Instruments 1510A Precision Signal/Function Generator Cable & Wire troubleshooting is important to identify and resolve problems with electrical or data transmission systems. Without proper troubleshooting, systems can fail, causing a range of issues including downtime, lost productivity and safety hazards. MTI Instruments 1510A is ideal for troubleshooting in the instrumentation room, factory floor, flight-line or laboratory. 1510A Key Benefits The 1510A is a portable signal source used for calibrating electronic equipment and machinery monitoring systems. Its portability and ruggedness make it ideal for use in the instrumentation room, [...]
led substrate sapphire thickness
N/A led substrate sapphire thickness Displacement Remember that old acronym, GIGO? Garbage in garbage out, it can apply to raw materials as well as programming. Sapphire wafers need to be of a certain quality to ensure maximum yield. EXCESSIVE TTV, BOW, AND WARP LEAD TO PREMATURE LED FAILURE LED MANUFACTURERS NEED TO INSPECT INCOMING WAFERS. WAFER PRODUCERS ALSO NEED TO CHECK AND CONTROL TTV, BOW AND WARP. The market for sapphire wafers, driven by the growth in LED manufacturing, is booming. While the price has come down significantly since 2011, the size of the wafers [...]
Dynamic Measurement of Armature Gaps
Introduction In large motors and generators, the air gap needed to separate the revolving rotor from the stator should be as small as possible. This reduces the magnetizing power requirement which needs to be large enough to prevent contact between the two, despite manufacturing tolerances on their dimensions or movement resulting from mechanical deflection or looseness in supporting bearings. The gap should also be uniform; a non-uniform gap causes increased noise and vibration. Since large generators and motors are usually quite expensive, it's advisable to monitor the gap to prevent catastrophic failure should the rotor or stator expand due to [...]
Closed Loop, Non-woven Conductive Film Thickness Measurement and Control Solution
Closed Loop, Non-woven Conductive Film Thickness Measurement and Control Solution Animation showing a system setup used to measure the thickness of thin conductive films such as electric vehicle (EV) battery electrodes. Description Learn how to measure EV battery plate thickness with MTI's Digital Accumeasure, a high-precision capacitance measurement system with nanometer accuracy and stability. Problem Lithium battery plates for electric vehicles consist of lithium ion compounds applied to either a copper plate substrate (cathode plate) or an aluminum substrate (anode plate). The plates are approximately 100-200 um thick ( .004 [...]
Vibration and Balancing Systems: The Spectrum Plot
Vibration and Balancing Systems: The Spectrum Plot Aviation / Aerospace Engine Balancing Vibration Description The Spectrum Plot: Types of Aircraft Vibration One of the least understood features of the PBS series of vibration analyzers is the spectrum function. The spectrum functionality is a more difficult function to understand, but once mastered, technicians can quickly develop an extremely in-depth understanding on what is going on in an engine during a test. Figure 1, below, shows a basic spectrum from the PBS system. On the x-axis is frequency, measured in Hz (per second). [...]
Thickness Information of Composite Materials
Thickness Information of Composite Materials Industrial Thickness Information Of Composite Materials Thickness Description Introduction: Composite materials consist of two or more materials which include a substrate or base material such as paper, cotton cloth, or glass cloth along with a resin or adhesive such as epoxy, melamine, or silicone. To make a thermoset laminate, the base material is coated with the adhesive so that layers of material can be pressed under heat and pressure into sheet form. The Problem: Composite material thickness needed to be verified prior to forming or [...]
Capacitance Probe Detects Water Contamination in Oiling Systems
Capacitance Probe Detects Water Contamination in Oiling Systems Industrial, Research & Development Capacitance Probe Detection of Water Contamination Metrology, Tolerances Description [Application Note 12218]  The adverse effects of water in oil are well known. Negative consequences include higher viscosity reduced load carrying ability hydrolysis (the formation of acids, sludge, and varnish) foam formation and air entrainment additive depletion corrosion on metal surfaces loss of lubrication film strength leading to increased wear cavitations filter plugging Problem As oil system reliability decreases, maintenance and repair activities increase. Corrective action must be taken [...]