Tape Cartridge Movement
Tape Cartridge Movement Semiconductor Tape Cartridge Movement Positioning Description Researchers are presently working on drives with track widths in the 5 to 1 micron region. For these small widths, tape wander, properly called Lateral Tape Movement (LTM), must be less than 1 micron. This is because the track following head always lags the moving target and produces a position error signal. If the position error signal gets to be larger than about 1/10 the track width, the track cannot be read. However, it follows that the smaller the LTM, the [...]
Wafer QA/QC After Slicing And Polishing
Wafer QA/QC After Slicing And Polishing Semiconductor Wafer Qa/Qc After Slicing And Polishing Surface Description Introduction:When wafers are sliced up with wire saws, they are measured to make sure they are within the specified thickness, with minimal bow, warp, and TTV. After initial measurement, they are sorted and sent for polishing. Since polishing removes material and smoothes out the rough surfaces they need to be measured again to ensure they meet thickness guidelines and quality standards. Solution:MTI Instruments manufactures multiple systems to perform thickness measurements. From semi automated Proforma 300SA to manual [...]
Mobile Devices
Consumer Electronics Mobile Devices Dimensions Description
Height Gap Of Inkjet Printers
Height Gap Of Inkjet Printers Consumer Electronics Height Gap Of Inkjet Printers Positioning Description Introduction:  Inkjet printers require a certain distance between the inkjet print head and the paper. If the distance is set incorrectly, the printed images get blurry. Current state of the art printers have the print head nozzles built right into the bottom of the ink reservoir (B) as shown below. When the ink cartridge is installed in the printer, the inkjet nozzles (made out of silicon) essentially become a grounded target through the connections shown at [...]
Electronics Parts Profiling
Electronics Parts Profiling Consumer Electronics Electronics Parts Profiling Thickness Description MTI's 2D laser sensors can be used to scan 3D profiles of items such as printed circuit boards to verify all the parts are installed, making sure parts don’t exceed certain heights or that the part is present. You can even plot or examine the image intensity profile of the 2D sensor which yields a monochromatic image of the target and this can be used with OCR software or barcode software to recognize product codes, check if labels are present or [...]
Glass Thickness
Glass Thickness Consumer Electronics Glass Thickness Thickness Description Did you know that glass thickness can be measured with a capacitance probe? You will need some equipment: Digital Accumeasure D200 ASP-2500-CTA Dielectric probe (The capacitance probe has a sensing area of 11.25 mm) Range extension = 3X, 10Hz filter Introduction:  An industrial glass fabricator needed a way to determine the thickness of glass, before cutting it to shape and coating it. The glass sample was marked with indices to find the measuring points. The sample center point -5- thickness was checked with [...]
Piezo Stage Positioning
Piezo Stage Positioning Consumer Electronics Piezo Stage Positioning Description Positioning stages using piezoelectric stack actuators (PEA) have very high resolution. However, it is difficult to achieve precise dynamic motion tracking using traditional linear controllers such as PID due to the inherent hysteresis nonlinearity of piezoelectric materials and the phase lag associated with such controllers. Capacitance Sensors are ideal for measuring the actual piezo stage position and correcting for the inherent nonlinearity through closed loop feedback. They have the stability, bandwidth and high resolution needed to do the job. Several of MTI’s [...]
Thread Checking
Automotive Thread Checking Presence/Absence Description Manual thread inspection is slow, not always reliable and tedious for the inspector. Manufacturers have struggled to come up with ways to reliably automate the process at a reasonable cost. Automated systems are available that use “screw sensors” can quickly wear or be cross threaded, requiring operator attention and a tooling change. A worn screw can provide false rejections leading to the unnecessary scrapping of parts. Capacitance solutions are cost effective alternative which are becoming increasingly popular due to their high reliability and fast measurement speed. Special cylindrical “ring [...]
TESTING CHARGE AMPLIFIER GAIN AND FREQUENCY RESPONSE WITH A SIGNAL GENERATOR
[Application Note 40518] Piezoelectric transducers produce small electrical charges in response to pressure. Their sensitivity, ruggedness, and stability at high temperatures make them an essential building block of many accelerometers and pressure sensors. Applications include turbine vibration measurement (accelerometers) and combustion dynamics monitoring (pressure sensors). Typically, the high-impedance charge output produced by a piezoelectric transducer must be conditioned and amplified before transmission across system cabling to the data acquisition and measurement instrumentation. This conversion is accomplished with a device called a charge amplifier. Problem Over time, a charge amplifier’s signal response can drift. Damage to the charge amplifier or associated [...]
THICKNESS INFORMATION OF COMPOSITE MATERIALS
Composite materials consist of two or more materials which include a substrate or base material such as paper, cotton cloth, or glass cloth along with a resin or adhesive such as epoxy, melamine, or silicone. To make a thermoset laminate, the base material is coated with the adhesive so that layers of material can be pressed under heat and pressure into sheet form. The Problem: Composite material thickness needed to be verified prior to forming or machining. Due to the size of the sheets typical measurement techniques were not suitable. A consistent method to accurately measure the board thickness [...]







