MTI-Website Download Access
Please complete the form below to access MTI downloadable documents. MTI Instruments by Vitrek 900 N. State Street Lockport, IL 60441 Phone: (815) 838-0005 Fax: (518) 218-2506 sales@mtiinstruments.com
Wafer Thickness, Bow, Warp And TTV
Semiconductor Wafer Thickness, Bow, Warp And Ttv Surface Description Thickness Measurement ASTM F657: The distance through a wafer between corresponding points on the front and back surface. Thickness is expressed in microns or mils (thousandths of an inch). Total Thickness Variation (TTV) ASTM F657: The difference between the maximum and minimum values of thickness encountered during a scan pattern or series of point measurements. TTV is expressed in microns or mils (thousandths of an inch). Figure above shows a wafer placed between two non-contact measurement probes. By monitoring changes between the upper probe face [...]
MTI-Website E-Mail Sign-Up
Please complete the form below to be added to Vitrek's Distribution Lists. You may unsubscribe at any time by emailing unsubscribe@vitrek.com. MTI Instruments by Vitrek 900 N. State Street Lockport, IL 60441 Phone: (800) 342-2203 Outside North America: (518) 218-2550 Fax: (518) 218-2506 sales@mtiinstruments.com
Tape Cartridge Movement
Tape Cartridge Movement Semiconductor Tape Cartridge Movement Positioning Description Researchers are presently working on drives with track widths in the 5 to 1 micron region. For these small widths, tape wander, properly called Lateral Tape Movement (LTM), must be less than 1 micron. This is because the track following head always lags the moving target and produces a position error signal. If the position error signal gets to be larger than about 1/10 the track width, the track cannot be read. However, it follows that the smaller the LTM, the [...]
MTI-Website Laser Solutions Google Ads
Please complete the form below to request information on MTI Instruments Products. MTI Instruments by Vitrek 900 N. State Street Lockport, IL 60441 Phone: (800) 342-2203 Outside North America: (518) 218-2550 Fax: (518) 218-2506 sales@mtiinstruments.com
MTI-Website Product Registration
Please complete the form below to register your MTI Instruments product. MTI Instruments by Vitrek 900 N. State Street Lockport, IL 60441 Phone: (800) 342-2203 Outside North America: (518) 218-2550 Fax: (518) 218-2506 sales@mtiinstruments.com
Wafer QA/QC After Slicing And Polishing
Wafer QA/QC After Slicing And Polishing Semiconductor Wafer Qa/Qc After Slicing And Polishing Surface Description Introduction:When wafers are sliced up with wire saws, they are measured to make sure they are within the specified thickness, with minimal bow, warp, and TTV. After initial measurement, they are sorted and sent for polishing. Since polishing removes material and smoothes out the rough surfaces they need to be measured again to ensure they meet thickness guidelines and quality standards. Solution:MTI Instruments manufactures multiple systems to perform thickness measurements. From semi automated Proforma 300SA to manual [...]
MTI-Website Proforma 5 Common Mistakes Download
Please complete the form below to download the document MTI Instruments by Vitrek 900 N. State Street Lockport, IL 60441 Phone: (800) 342-2203 Outside North America: (518) 218-2550 Fax: (518) 218-2506 sales@mtiinstruments.com
Mobile Devices
Consumer Electronics Mobile Devices Dimensions Description
MTI- Website Service & Repairs Inquiry
Please complete the form below for information on service and repair of MTI Instruments products. MTI Instruments by Vitrek 900 N. State Street Lockport, IL 60441 Phone: (815) 838-0005 Fax: (518) 218-2506 sales@mtiinstruments.com